User Tools

Site Tools

Trace: • Flyingbearp902 build
flyingbearp902_build

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
flyingbearp902_build [2017/03/10 18:34]
greg 		flyingbearp902_build [2017/04/02 20:28] (current)
greg
Line 58: Line 58:
  
 To do so, in the configuration.h files, there is lines 434 to 438 and lines 710-711 to modify accordingly. Also, on the ramps board, the endstops need to be moved from Xmin Ymin to Xmax Ymax. I could design holders to have the endstops at (0,0), but first, I need a 3D printer ;) To do so, in the configuration.h files, there is lines 434 to 438 and lines 710-711 to modify accordingly. Also, on the ramps board, the endstops need to be moved from Xmin Ymin to Xmax Ymax. I could design holders to have the endstops at (0,0), but first, I need a 3D printer ;)
 +
 +Also in configuration.h, line 723, replace 220 by 230.
 +
 +=== Laser installation ===
 +
 +Needs longer fans screws, new length = ?
 +
 +3d model https://3dwarehouse.sketchup.com/model/ff66f756-fd29-4d73-9d4b-a9ca45f8ea47/lcheapo-laser-holder-for-flyingbear-v01
 +
 +In Marlin firmware, in configuration.h, line 724, replace 220 by 200 (important)
  
 === Silent motors === === Silent motors ===
Line 63: Line 73:
 https://www.filastruder.com/products/silentstepstick-tmc2100-stepper-motor-driver https://www.filastruder.com/products/silentstepstick-tmc2100-stepper-motor-driver
  
-=== Linear bearings === 
  
-Planning to replace all bearings with http://www.ebay.ca/itm/222402964193 or https://emvioeng.com/shop/3d-printing/3d-printer-components/drylin-bearings-for-8mm-shaft-15mm-od/ (need 8), less game, less noise. 
  
 ------ ------
Line 94: Line 102:
 - The wiring for all stepper motors (including the extruder) had to be mirrored relative to the graphic in the instructions. - The wiring for all stepper motors (including the extruder) had to be mirrored relative to the graphic in the instructions.
 - The throat of the extruder/hotend had to be screwed up further towards the filament inlet, as it was impossible to feed the filament into the throat deep down otherwise. - The throat of the extruder/hotend had to be screwed up further towards the filament inlet, as it was impossible to feed the filament into the throat deep down otherwise.
 +
 +Upgrades:
 +
 +=== Linear bearings ===
 +
 +Chinese linear bearings have game, are noisy, and will eat up your rod (https://youtu.be/ZGBipbgwgME?t=6m21s)
 +
 +Replace all bearings with http://www.ebay.ca/itm/222402964193 or https://emvioeng.com/shop/3d-printing/3d-printer-components/drylin-bearings-for-8mm-shaft-15mm-od/ (need 8), less game, less noise.
 +
 +
flyingbearp902_build.1489199662.txt.gz · Last modified: 2017/03/10 18:34 by greg

Page Tools

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki